It is the rare person who does not deal with electrical appliances today. Most people watch television, turn the oven on to cook food, or simply pop frozen foods into the microwave. With electricity pouring through virtually every home, everyone should be aware of the following electrical safety precautions:
1. Never use electrical devices that have damaged or frayed wires.
The thick wires that connect an electrical device to the wall for energy are designed to safely transfer electricity from the socket to the device. When those wires tear apart, fray, or otherwise become damaged, they can allow the flow of electricity to escape the wire. This can lead to a shock of you grab the wire in that area, but it can also lead to an electrical fire. Safety precautions require you to throw these appliances out if you cannot replace the wire.
2. Play it safe with water in close vicinity to electrical devices.
When water comes in contact with an electrical outlet or electrical device plugged into the wall, it can become live with electricity and present a danger to humans. If you have a flood in your home, do not step into the water if it is covering electrical outlets. Do not place electrical devices where they can fall into a sink or bathtub full of water.
3. Watch the placement of cords leading to electrical devices.
All electrical devices have cords, and it is common to run longer cords along the wall in order to place them where you want them. The problem is you can create a tripping hazard if you run cords along doorways or across floors in heavy traffic areas of your home. Carefully place cords where they are safe for everyone in your home.
4. If you are going to change parts on or repair an electrical device, you have to disconnect it from the outlet or otherwise shut off electrical flow to the device.
Never do work on or repair an electrical device while it is live with electricity. In most cases this just means unplugging the device before you open it up to make repairs, but when doing home improvement projects it could mean shutting off electricity from the breaker box. If you don’t know how to do this, then do not attempt the repairs on your own.
All of these electrical safety precautions should be remembered by adults working with electrical appliances. If you know someone who isn’t aware of any precaution on this list, send them here to learn. It could save a life!
When in doubt, call an electrician from Marbec Enterprises and have them take the worry out!
Longwood, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en
Showing posts with label longwood. Show all posts
Showing posts with label longwood. Show all posts
Tuesday, July 26, 2016
Wednesday, January 27, 2016
Industrial wiring & residential wiring for electricity, is a complex task.
Whether you’re doing industrial wiring or residential wiring for electricity, you’ve got a complex task ahead of you. Needless to say, industrial wiring is essentially a much more complex form of residential wiring. Let an electrician at Marbec Enterprises take care of it for you. We will simply provide you with a very basic overview of what you need to understand with regard to residential wiring and industrial wiring.
It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns. Marbec Enterprises is
trained in all aspects of electrical work.
Basics of Doing Residential Wiring
Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.
The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.
White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.
A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.
Basics of Doing Industrial Wiring
Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.
There are four types of 3-phase electrical power:
Common 3 Wire
Common 4 Wire
3 Wire with Grounded Hot Leg
Special 4 Wire
No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.
Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.
The Marbec Electrical team of highly trained commercial electrical contractors has provided top quality electrical installations for large commercial building projects in Florida for over 10 years. We are trained in all aspects of commercial electrical work and offer extensive expertise and professional service to our clients.
Winter Garden, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com |plus.google.com/102338195995648896384/posts?hl=en
It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns. Marbec Enterprises is
trained in all aspects of electrical work.
Basics of Doing Residential Wiring
Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.
The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.
White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.
A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.
Basics of Doing Industrial Wiring
Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.
There are four types of 3-phase electrical power:
Common 3 Wire
Common 4 Wire
3 Wire with Grounded Hot Leg
Special 4 Wire
No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.
Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.
The Marbec Electrical team of highly trained commercial electrical contractors has provided top quality electrical installations for large commercial building projects in Florida for over 10 years. We are trained in all aspects of commercial electrical work and offer extensive expertise and professional service to our clients.
Winter Garden, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com |plus.google.com/102338195995648896384/posts?hl=en
Subscribe to:
Posts (Atom)