Industrial and Residential Wiring

Whether you’re doing industrial wiring or residential wiring for electricity, you’ve got a complex task ahead of you. Needless to say, industrial wiring is essentially a much more complex form of residential wiring. Let an electrician at Marbec Enterprises take care of it for you. We will simply provide you with a very basic overview of what you need to understand with regard to residential wiring and industrial wiring.
It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns. Marbec Enterprises is trained in all aspects of electrical work.

Basics of Doing Residential Wiring
Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.
The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.
White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.

A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.

Basics of Doing Industrial Wiring
Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.

There are four types of 3-phase electrical power:
Common 3 Wire
Common 4 Wire
3 Wire with Grounded Hot Leg
Special 4 Wire

No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.
Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.

The Marbec Electrical team of highly trained commercial electrical contractors has provided top quality electrical installations for large commercial building projects in Florida for over 10 years. We are trained in all aspects of commercial electrical work and offer extensive expertise and professional service to our clients.

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Light Switch Or Outlet Not Functioning Correctly

When a light switch or electrical outlet doesn’t function correctly, a professional electrician from Marbec Enterprises can trace this back to a variety of causes. First, it’s possible this non-functioning device was never connected to the wiring in your building. Secondly, the circuit affected by a switch or outlet may not be completed because of another component. For example: A switch may control an outlet which is unoccupied by a lamp or any other electrical device. Also, an outlet may be connected to a switch which is in the off position. A third cause might be related to a defective breaker, or a breaker which was tripped or turned off, but never switched back on. However, a fourth possibility may relate to a much larger problem.

Sometimes, a switch or outlet fails when it is damaged by arcing. If the arcing was caused by a connection to aluminum wiring, great potential hazards exist. If your home or building was constructed or renovated before 1972, or during the late sixties, it may contain aluminum wiring. Aluminum wiring was used legally during those years, but outlawed for installation in new homes, commercial buildings, remodels and renovations after it was identifie

d with conditions which could lead to electrical fires.

Although aluminum wiring itself is generally no more hazardous than copper, its splices and connections with other metals present a real hazard because they can become corroded and begin arcing. Because arcing in these connections can lead to fire within surrounding materials, aluminum wire was discontinued. However, many homes still contain aluminum wiring, and research conducted by the Consumer Product Safety Commission (CPSC) reveals that buildings with aluminum wiring pose a fire risk which is 55 times greater than the risks with similar structures wired with copper. So, if you discover an electrical outlet or switch which doesn’t appear to be functioning correctly, it’s possible this outlet or switch was damaged by a connection with aluminum wiring. If you have safety questions about this type of problem, or any electrical concerns regarding your residence or commercial building, please contact an electrician at Marbec Enterprises. Our licensed electricians are trained and equipped, and they can repair any type of electrical problem

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

7 tips to keep your family safe

As a Marbec Electrician we know that your family’s safety is one of the most important things on your mind throughout the day, so we decided that now would be a good time to re-visit the subject of Smoke Detector Replacement and maintenance. As the weather is cooling off, it is very important that you are certain your family is protected in the unfortunate event that you experience a house fire. According to the U.S. Fire Administration, “Each year fires occurring during the holiday season claim the lives of over 400 people, injure 1,650 more, and cause over $990 million in damage.” Remember these lucky
7 tips to keep your family safe this holiday season by ensuring that smoke detectors are installed correctly in your home, and that they are all in working order.

Smoke Detector Battery Replacement: At least once a year
One of the most important things to remember, if you already have smoke detectors installed in your home, is to replace the batteries at least once a year. An easy way to remember this is to change the batteries in your smoke detectors when you change your clocks for daylight savings time every year. Picking up this helpful habit makes it much easier to remember.

Smoke Detector Replacement: Every 5 to 7 years
Many smoke detector manufacturers recommend replacing the smoke detector unit itself every ten years, but a smoke detector’s reliability will actually decrease after 5 to 7 years. While this may seem like an extra cost, it is certainly a small price to pay for making sure that your family will have the most reliable method of early warning in the event of a fire, providing vital time for everyone to get out safely.

Smoke Detector Cleaning: At least twice a year
Dust, cobwebs, insects, and other airborne particles that make their way into our homes can collect on sensors and contaminate the circuitry inside your smoke detector, causing it to be less effective at sensing smoke. This is one of the most forgotten factors simply because many homeowners aren’t aware of the effects that dirt and dust can have on a smoke detector. Think about how dirty the blades of your ceiling fan would get if you never cleaned them. The same dust that accumulates on your fan blades will accumulate inside your smoke detector. At least twice a year, use your vacuum cleaner wand attachment to carefully remove dust and other contaminants from the inside and outside of your smoke detector.

Smoke Detector Types: Ionization, Photoelectric, or Both
There are two commonly used types of smoke detectors, each with their own advantages and disadvantages. Ionization style smoke detectors are more responsive to quick moving, high flaming fires, while photoelectric smoke detectors are more responsive to smoldering fires that produce more smoke. You can never know what type of fire will happen in your home, so a great option to ensure the best protection is to choose smoke detector units that provide both ionization and photoelectric detection of smoke and fire.

Smoke Detector Location: Key guidelines for safe placement
Smoke detector placement is highly important in order for them to work properly. When installing smoke detectors in your home, it is ideal to have a smoke detector in each room, but at the very least, you should install smoke detectors on every level of your home, and in hallways near each bedroom to increase the likelihood that your family will be able to hear them even while sleeping. Smoke detectors should be placed 6 to 12 inches from the ceiling, and you should avoid installing them near vents, fireplaces, or kitchen appliances to reduce the accumulation of dust, soot, and oily residues from cooking.

Interlinked Smoke Detectors: Whole house warning
Modern smoke detector systems are more than simply individual detectors. It is recommended to install a system that allows all of the smoke detectors in your home to communicate with each other causing all of the detectors to alert of the fire if any single detector senses one. These systems can be wired directly into your homes electrical system, or allow wireless communication between each smoke detector. This has been a major advancement in smoke detector technology, allowing more time for residents to escape if a fire begins in any area of the home. These systems are especially valuable in late-model homes where the master bedroom is often on the opposite side of the house from children’s rooms.

Smoke Detector Testing: At least twice a year
We often take for granted that a smoke detector will simply work as designed once it is installed, but as you can see from this list, there are a lot of factors that go into a reliable smoke detection system. At the very least, make sure that you test your smoke detectors twice a year using the test button that is located on the smoke detector unit itself. When testing interlinked smoke detector systems, be sure to verify that all of the other detectors in your home alert when you test each unit individually. Even if a unit alerts when you test it, if it does not cause the other units in the home to alert, that means that there is an issue with communication between the units, and it should be inspected by a licensed Marbec Electrician.

If you have any concerns about your smoke detector system, or any other electrical projects in your home, the electricians at Marbec Enterprises. will be happy to help. Reach out to us by phone or through the “Contact Us” page on our website, and let our professional electrical technicians ensure your family’s safety by guaranteeing that the job is done right!

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

At Marbec Enterprises (MarbecElectric.com), we pride ourselves in knowing the capability we have of meeting all types of construction demands and deadlines.

We understand the importance of all field and project management coordination to bring all our construction projects on time and on budget. Our field and office staff continues to bring a personal commitment to providing our customers with solutions, answers, and support for all electrical concerns.

Our background has been in multi-family housing, commercial office space, research and development, clean rooms, high tech fabrications, student housing, restaurants, and all types of tenant improvements, shells and cores, hospital and health care facilities, building renovations, high rise buildings, hotels, government buildings, fire alarm and security system, and tele/data installations.

***Design-Build, Engineering Analysis, and Budget Pricing***

During our partnering of design build projects, we have established strong loyal relationships with the area’s top general contractors, owners, and construction managers and provide complete assistance during the design/development phase of the project. Marbec Electric can assist with project budgeting, value engineering options and constructability recommendations.

We are experienced in all types of fast-track design build projects including tenant improvement, shells, site work, and clean rooms.

Our coordination with construction and project management teams, field staff, utility companies, and estimators solves all the construction requirements for our clients. Learn more at: marbecelectric.com

Longwood, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Never use electrical devices that have damaged or frayed wires

It is the rare person who does not deal with electrical appliances today. Most people watch television, turn the oven on to cook food, or simply pop frozen foods into the microwave. With electricity pouring through virtually every home, everyone should be aware of the following electrical safety precautions:

1. Never use electrical devices that have damaged or frayed wires.
The thick wires that connect an electrical device to the wall for energy are designed to safely transfer electricity from the socket to the device. When those wires tear apart, fray, or otherwise become damaged, they can allow the flow of electricity to escape the wire. This can lead to a shock of you grab the wire in that area, but it can also lead to an electrical fire. Safety precautions require you to throw these appliances out if you cannot replace the wire.

2. Play it safe with water in close vicinity to electrical devices.
When water comes in contact with an electrical outlet or electrical device plugged into the wall, it can become live with electricity and present a danger to humans. If you have a flood in your home, do not step into the water if it is covering electrical outlets. Do not place electrical devices where they can fall into a sink or bathtub full of water.

3. Watch the placement of cords leading to electrical devices.
All electrical devices have cords, and it is common to run longer cords along the wall in order to place them where you want them. The problem is you can create a tripping hazard if you run cords along doorways or across floors in heavy traffic areas of your home. Carefully place cords where they are safe for everyone in your home.

4. If you are going to change parts on or repair an electrical device, you have to disconnect it from the outlet or otherwise shut off electrical flow to the device.
Never do work on or repair an electrical device while it is live with electricity. In most cases this just means unplugging the device before you open it up to make repairs, but when doing home improvement projects it could mean shutting off electricity from the breaker box. If you don’t know how to do this, then do not attempt the repairs on your own.

All of these electrical safety precautions should be remembered by adults working with electrical appliances. If you know someone who isn’t aware of any precaution on this list, send them here to learn. It could save a life!

When in doubt, call an electrician from Marbec Enterprises and have them take the worry out!

West Volusia, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Correct safety & maintenance of your hot water heater.

The hot water heater represents one of the greatest hazards in the modern home, yet far too many homeowners have never read their heater’s owner’s manual. Common dangers associated with these household appliances include severe burns from scalding water, electric shock hazards, explosions, and fire.

Because most water heaters reside in closets, basements and garages, and are for the most part hidden from our daily lives, many aren’t as aware as they should be of the maintenance and precautions which are necessary for safety. Many homeowners don’t know for instance, that they should drain and flush a hot water heater every six months, to prevent sediment buildup. Others are unaware that hydrogen gas can build up inside electrically heated hot water systems when they remain inactive for two weeks or more. Hydrogen buildup requires carefully performed procedures to safely remove this flammable gas from hot water pipes. Many don’t know how and why water softening systems shorten the lives of water heaters, or that every electric hot water heater should be properly grounded with the correct gauge of copper wire. Marbec Enterprises can do this.

Correct safety and maintenance measures covered in a water heater’s manual are extremely important for household safety, so every homeowner should study this to learn how to properly maintain their hot water systems. It’s also extremely important to understand the electrical dangers these appliances represent. Because a hot water heater contains electrical heating elements immersed in water, these elements can deteriorate with age and short out electrically to the water heater’s metal casing. When this happens, it’s possible to receive a severe and perhaps fatal shock when touching the hot water heater’s housing or connecting pipes. If you do not have the necessary skills to work safely around high voltage electrical conditions, you should always call a professional electrician at Marbec Enterprises any time you suspect a problem with your hot water heater or when you have any other electrical concerns. When any questions about electrical safety arise, please call Marbec Enterprises. Our electricians are trained and equipped to identify any type of hazardous electrical condition, and to determine the proper repair procedures.

West Volusia, FL | (386) 956-1594 | marbecelectric.com |twitter.com/MarbecElectric | marbecelectric.tumblr.com |plus.google.com/102338195995648896384/posts?hl=en