Industrial and Residential Wiring

Whether you’re doing industrial wiring or residential wiring for electricity, you’ve got a complex task ahead of you. Needless to say, industrial wiring is essentially a much more complex form of residential wiring. Let an electrician at Marbec Enterprises take care of it for you. We will simply provide you with a very basic overview of what you need to understand with regard to residential wiring and industrial wiring.
It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns. Marbec Enterprises is trained in all aspects of electrical work.

Basics of Doing Residential Wiring
Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.
The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.
White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.

A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.

Basics of Doing Industrial Wiring
Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.

There are four types of 3-phase electrical power:
Common 3 Wire
Common 4 Wire
3 Wire with Grounded Hot Leg
Special 4 Wire

No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.
Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.

The Marbec Electrical team of highly trained commercial electrical contractors has provided top quality electrical installations for large commercial building projects in Florida for over 10 years. We are trained in all aspects of commercial electrical work and offer extensive expertise and professional service to our clients.

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Arc fault Circuit Interrupter

As its name implies, an Arc fault Circuit Interrupter is designed to detect electrical arcing, and turn off the current to wiring or appliances where arcing is occurring. An electrical arc occurs anytime an electric current jumps through a gap or airspace between two conductors. This typically produces a visible spark, or sparks. We’re all familiar with small sparks which can be seen inside electric tools and motors, and tiny sparks which may occur when we plug an electrical device into a wall outlet. Small levels of arcing are normal and benign in these places, but dangerous arcing is a different matter. Dangerous levels of arcing can involve damaged insulation, worn or broken conductors, many other electrical problems. This type of arcing is the single greatest cause for electrical fires across our continent, and has resulted in hundreds of human fatalities, hundreds of thousands of fires, and billions of dollars in property damages. AFCI’s are designed to detect dangerous levels of arcing while ignoring benign occurrences. When dangerous arcing occurs, an AFCI will immediately detect this and turn off the electrical current for the affected circuit. If someone tries to reset the AFCI, and it trips again rapidly, this is typically an indicator of a larger problem.

While a GFCI is designed to detect electricity which has become shorted to ground, an AFCI is designed to detect arcing within wiring or electrical devices or appliances. AFCI units look a lot like circuit breakers, and are typically located inside breaker boxes, rather than outlets. However, they are able to detect dangerous arcing conditions a breaker cannot detect. In addition, AFCIs are manufactured for circuits carrying up to 100 amps, s
o they can protect buildings from arcing in large equipment like stoves and central air units.

AFCIs have been developed and mandated by law to protect lives and property from electrical fires caused by arcing. However, many older homes and buildings have not been retrofitted with these devices and remain unprotected. To make matters worse, older buildings are more likely to have outdated wiring and appliances, and insulation problems and other conditions which cause arcing problems. If you are concerned about your wiring and would like to schedule a safety inspection, call Marbec Enterprises. Our electricians are licensed and equipped to inspect electrical systems, and can determine if your home or building is sufficiently protected by AFCI protective devices.

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

7 tips to keep your family safe

As a Marbec Electrician we know that your family’s safety is one of the most important things on your mind throughout the day, so we decided that now would be a good time to re-visit the subject of Smoke Detector Replacement and maintenance. As the weather is cooling off, it is very important that you are certain your family is protected in the unfortunate event that you experience a house fire. According to the U.S. Fire Administration, “Each year fires occurring during the holiday season claim the lives of over 400 people, injure 1,650 more, and cause over $990 million in damage.” Remember these lucky
7 tips to keep your family safe this holiday season by ensuring that smoke detectors are installed correctly in your home, and that they are all in working order.

Smoke Detector Battery Replacement: At least once a year
One of the most important things to remember, if you already have smoke detectors installed in your home, is to replace the batteries at least once a year. An easy way to remember this is to change the batteries in your smoke detectors when you change your clocks for daylight savings time every year. Picking up this helpful habit makes it much easier to remember.

Smoke Detector Replacement: Every 5 to 7 years
Many smoke detector manufacturers recommend replacing the smoke detector unit itself every ten years, but a smoke detector’s reliability will actually decrease after 5 to 7 years. While this may seem like an extra cost, it is certainly a small price to pay for making sure that your family will have the most reliable method of early warning in the event of a fire, providing vital time for everyone to get out safely.

Smoke Detector Cleaning: At least twice a year
Dust, cobwebs, insects, and other airborne particles that make their way into our homes can collect on sensors and contaminate the circuitry inside your smoke detector, causing it to be less effective at sensing smoke. This is one of the most forgotten factors simply because many homeowners aren’t aware of the effects that dirt and dust can have on a smoke detector. Think about how dirty the blades of your ceiling fan would get if you never cleaned them. The same dust that accumulates on your fan blades will accumulate inside your smoke detector. At least twice a year, use your vacuum cleaner wand attachment to carefully remove dust and other contaminants from the inside and outside of your smoke detector.

Smoke Detector Types: Ionization, Photoelectric, or Both
There are two commonly used types of smoke detectors, each with their own advantages and disadvantages. Ionization style smoke detectors are more responsive to quick moving, high flaming fires, while photoelectric smoke detectors are more responsive to smoldering fires that produce more smoke. You can never know what type of fire will happen in your home, so a great option to ensure the best protection is to choose smoke detector units that provide both ionization and photoelectric detection of smoke and fire.

Smoke Detector Location: Key guidelines for safe placement
Smoke detector placement is highly important in order for them to work properly. When installing smoke detectors in your home, it is ideal to have a smoke detector in each room, but at the very least, you should install smoke detectors on every level of your home, and in hallways near each bedroom to increase the likelihood that your family will be able to hear them even while sleeping. Smoke detectors should be placed 6 to 12 inches from the ceiling, and you should avoid installing them near vents, fireplaces, or kitchen appliances to reduce the accumulation of dust, soot, and oily residues from cooking.

Interlinked Smoke Detectors: Whole house warning
Modern smoke detector systems are more than simply individual detectors. It is recommended to install a system that allows all of the smoke detectors in your home to communicate with each other causing all of the detectors to alert of the fire if any single detector senses one. These systems can be wired directly into your homes electrical system, or allow wireless communication between each smoke detector. This has been a major advancement in smoke detector technology, allowing more time for residents to escape if a fire begins in any area of the home. These systems are especially valuable in late-model homes where the master bedroom is often on the opposite side of the house from children’s rooms.

Smoke Detector Testing: At least twice a year
We often take for granted that a smoke detector will simply work as designed once it is installed, but as you can see from this list, there are a lot of factors that go into a reliable smoke detection system. At the very least, make sure that you test your smoke detectors twice a year using the test button that is located on the smoke detector unit itself. When testing interlinked smoke detector systems, be sure to verify that all of the other detectors in your home alert when you test each unit individually. Even if a unit alerts when you test it, if it does not cause the other units in the home to alert, that means that there is an issue with communication between the units, and it should be inspected by a licensed Marbec Electrician.

If you have any concerns about your smoke detector system, or any other electrical projects in your home, the electricians at Marbec Enterprises. will be happy to help. Reach out to us by phone or through the “Contact Us” page on our website, and let our professional electrical technicians ensure your family’s safety by guaranteeing that the job is done right!

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Marbec Enterprises can help save money on your electric bill!

In the current economic climate, in which everyone is trying to save money, you might not know that a Marbec electrician can help! Sometimes, saving money is as simple as finding a simple idea that makes your life run more efficiently. When it comes to electricity, one of the best and least utilized ways to save money and energy is by putting your lights on a timer.

As any Marbec electrician can tell you, timers are extremely useful! You can use them to turn lights on and off, whether or not you are at home. This makes it easy for you to appear as though you are home when you are on vacation, or control your Christmas lights, but those are not the only instances in which timers are a good idea. For instance, you can set a timer to make your lights turn off after you go to bed, and come back on in the morning. This makes a great backup alarm clock, and also ensures that you don’t accidentally leave lights on all night. You can also set them to turn off lights when you are at work, in case you forget.

There are two types of timers for home systems: mechanical and digital. Digital timers look good and are very useful, with several automated features. Even though they can be installed by someone who is not an electrician, homeowners may feel more secure hiring a professional, because digital timers have sensitive electronics inside that require a neutral wire that switches do not. A Marbec electrician will be able to choose the right digital timer for your needs, competently install it, and even change out the switch plates if necessary.

Mechanical timers are less common than digital, but are very useful. They are often used to control swimming pool equipment and outdoor lighting. In addition to controlling lights, they can be attached to a water heater to keep it from running when you don’t need hot water. This can make a huge difference in your electric bill!

The main difference between mechanical and digital timers is that mechanical timers are typically larger and sturdier, and can handle a larger electrical load. Digital timers are more aesthetically pleasing, and will fit better into your home’s décor. A competent Marbec Enterprises electrician will advise you as to which timer best suits your needs.

Whether you have an electrical problem, or are just looking for ways to
save money on your electric bill, Marbec Enterprises can help!  Visit our website or if you would prefer, you can always call us to schedule an appointment today!

Lake Helen, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Call Marbec Enterprises to Make Sure That Your Home is Safe & Free From the Risk of a Short or a Fire.

Tripped circuit breaker: many of us have experienced them at some point in our homes, yet instead of asking ourselves, “Why Do Breakers Trip?”, we reset the breaker without much thought. Before flipping the switch back over to the “ON” position, however, it’s important to understand why the breaker tripped in the first place, and what can be done to keep it from happening again.

At Marbec Enterprises we understand the danger of ignoring the warning signs of a tripped circuit breaker. But first, you need to know what a breaker does and how it works.

Simply put, a home or business circuit breaker is a safety device that monitors the amount of electrical current going through the electrical wires in your home and shuts off the circuit if too much electricity is being pulled through it, or if there is any disturbance in the current that could result in a fire.

Whereas a fuse performs the same task but can only be used once, a circuit breaker can perform over and over with the use of a switch that trips to indicate when it has effectively cut off current to a particular area.
So, Why Do Breakers Trip and what kind of things could cause a circuit breaker to trip? Some of the most common causes of a tripped breaker include:
Overloaded circuits: Often times, when there are too many appliances plugged into an electrical circuit, the wiring reaches unsafe heat levels due to pulling more electricity through the circuit than it is designed to accommodate,  and puts your home at a risk for a fire. That’s when the circuit breaker trips, shutting off everything that is plugged in to that circuit, preventing overheating, reducing the risk of fire. This happens often in older homes, where the wiring was not designed to withstand the power of modern appliances.
Electrical shorts: Other times, a tripped breaker can happen as a result of an electrical short, due to old and worn out appliances, with damaged wiring in your home. Common causes of electrical shorts in the home include faulty wiring, rodents or other animals chewing through your wires or aging wiring in older homes. Because of the large range of possible culprits, diagnosing an electrical short can be more difficult and therefore should not be ignored. Determining whether a short is in an appliance may be as simple as disconnecting your appliance and resetting the breaker, if it continues to trip, definitely call a Marbec Electrician. Often times, it’s when an appliance is not being used and the electrical short is happening, that it is much more complex and requires professional help.

Because of the many reasons why your circuit breaker could be tripping, and because of the purpose of the circuit breaker, you should never take a tripped breaker lightly. It’s important to understand that the circuit breaker is a safety device; simply switching the circuit back on without investigating the culprit can become costly in the long run and, in many cases, extremely dangerous.

If your breaker trips consistently, chances are there is a potentially dangerous electrical issue that needs to be looked at. Call Marbec Enterprises to make sure that your home is safe and free from the risk of a short or a fire.

Orlando, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=en

Commited to Excellence, Call Marbec Today!

Purpose:

Marbec Enterprises (MarbecElectric.com) exists to provide opportunities for each employee to maximize their personal and professional potential and to allow us to collectively making significant cultural and economic contributions to the communities in which we live and work.

Core Values:

Marbec Enterprises (MarbecElectric.com) upholds a commitment to EXCELLENCE in every endeavor; a commitment built on painstaking attention to detail and persistent communication and reflected in our superior quality of work and unparalleled customer service.

Marbec Enterprises (MarbecElectric.com) strives to provide a TEAM-ORIENTED atmosphere; one that promotes a positive attitude and encourages humble leadership and one that values each employee as an integral part of the Marbec Enterprises (MarbecElectric.com) family.

Doyle Electric embraces absolute INTEGRITY with employees, customers, end-users, consultants and every individual with whom we encounter; we are morally and ethically bound to do the right thing even when the right thing is not the easy, convenient, or profitable thing.

Marbec Enterprises (MarbecElectric.com) maintains a MERITOCRACY; an environment that seeks to reward continual personal and professional self-improvement and requires unfiltered honesty with ourselves and with each other.

Orange City, FL | (386) 956-1594 | marbecelectric.com | twitter.com/MarbecElectric | marbecelectric.tumblr.com | plus.google.com/102338195995648896384/posts?hl=

Easiest,quickest,cheapest way to transform your home!

Working with thousands of homeowners Marbec Enterprises has taken part in just about every home improvement project you can think up. Unfortunately, many homeowners’ plans for their dream home makeover have been put on hold due to a lack of funds. Fortunately, there are things that you can do to perform an affordable home makeover for a lot less than you might think.
By far, the most dramatic way to change the look and feel of your home, without a complete makeover, is by simply changing the way it shines! The lighting in your home plays a huge role in the first impression that you get when you walk into a room, and can be one of the major determining factors in setting the ambiance and overall feel of the room. By installing the proper recessed lights and pendant lights, along with chandeliers in your home, you will be able to accent the existing décor you already have.

Recessed can lighting will clean up your ceiling and do away with unsightly light fixtures installed everywhere.  When installing a recessed can, the type of trim is essential to maximizing the amount of light that you can get in an area.  A baffled or recessed trim will create a spotlight effect, whereas a flush mount trim allows the light to start at the ceiling and move throughout the room.  This gives a much more even look upon finished product.  Any electrician that has done a lot of installations should be able to guide you in the proper direction so that the style of lighting that you are looking for will be achieved.  Be careful attempting these by yourself, drywall will need to be cut for installation, and you never know where a wire or plumbing pipe may be hiding.

Pendant lighting is also making a big hit right now.  This type of lighting can be used to decoratively light up kitchen islands and kitchen bar-type counters.  This is a creative way to separate your kitchen from your living room.  Typically, homes are not pre-wired for these lights, and wiring will have to be added before they can be installed.  We highly suggest when wiring for these lights, that a new switch leg be installed for independent control.  As always, installing new wiring to your existing electrical should be done by a Marbec electrician.

Depending upon your tastes in furniture, replacing a living room of furniture can cost ten or twenty thousand dollars! Updating the lighting in the same room can drastically change the look and feel of the room, often for less than one thousand dollars. Replacing lamps and old fixtures with recessed can lighting and a classy chandelier can transform a dim dreary space into a room that you can be proud of. Switch out the chandelier with a nice ceiling fan that compliments the room, and you can even do your part in going green with the energy savings that come with using a fan to circulate the air in your home instead of relying constantly on your energy hogging air conditioning system!

If you need some help in creating your own affordable home makeover by replacing the out of date lighting in your home, contact an electrician at Marbec Enterprises to discuss the options available to upgrade.

West Volusia, FL | (386) 956-1594 | marbecelectric.com |twitter.com/MarbecElectric | marbecelectric.tumblr.com |plus.google.com/102338195995648896384/posts?hl=en

If your breaker trips consistently it could be dangerous!

Tripped circuit breaker: many of us have experienced them at some point in our homes, yet instead of asking ourselves, “Why Do Breakers Trip?”, we reset the breaker without much thought. Before flipping the switch back over to the “ON” position, however, it’s important to understand why the breaker tripped in the first place, and what can be done to keep it from happening again.
At Marbec Enterprises we understand the danger of ignoring the warning signs of a tripped circuit breaker. But first, you need to know what a breaker does and how it works.
Simply put, a home or business circuit breaker is a safety device that monitors the amount of electrical current going through the electrical wires in your home and shuts off the circuit if too much electricity is being pulled through it, or if there is any disturbance in the current that could result in a fire.

Whereas a fuse performs the same task but can only be used once, a circuit breaker can perform over and over with the use of a switch that trips to indicate when it has effectively cut off current to a particular area.

So, Why Do Breakers Trip and what kind of things could cause a circuit breaker to trip? Some of the most common causes of a tripped breaker include:
Overloaded circuits: Often times, when there are too many appliances plugged into an electrical circuit, the wiring reaches unsafe heat levels due to pulling more electricity through the circuit than it is designed to accommodate,  and puts your home at a risk for a fire. That’s when the circuit breaker trips, shutting off everything that is plugged in to that circuit, preventing overheating, reducing the risk of fire. This happens often in older homes, where the wiring was not designed to withstand the power of modern appliances.

Electrical shorts: Other times, a tripped breaker can happen as a result of an electrical short, due to old and worn out appliances, with damaged wiring in your home. Common causes of electrical shorts in the home include faulty wiring, rodents or other animals chewing through your wires or aging wiring in older homes. Because of the large range of possible culprits, diagnosing an electrical short can be more difficult and therefore should not be ignored. Determining whether a short is in an appliance may be as simple as disconnecting your appliance and resetting the breaker, if it continues to trip, definitely call a Marbec Electrician. Often times, it’s when an appliance is not being used and the electrical short is happening, that it is much more complex and requires professional help.

Because of the many reasons why your circuit breaker could be tripping, and because of the purpose of the circuit breaker, you should never take a tripped breaker lightly. It’s important to understand that the circuit breaker is a safety device; simply switching the circuit back on without investigating the culprit can become costly in the long run and, in many cases, extremely dangerous.

If your breaker trips consistently, chances are there is a potentially dangerous electrical issue that needs to be looked at. Call Marbec Enterprises to make sure that your home is safe and free from the risk of a short or a fire.

West Volusia, FL | (386) 956-1594 | marbecelectric.com |twitter.com/MarbecElectric | marbecelectric.tumblr.com |plus.google.com/102338195995648896384/posts?hl=en

Storm Season Tips

Storm Season Tips

With the weather in Florida being so unpredictable, how can you be sure that you are prepared to tackle what Mother Nature dishes out? Follow these simple tips to protect your home, your electrical system and your family from dangerous and frightening conditions.

#1 Have your electrical system checked regularly. With this storm season upon us, it is extremely important that you get in touch with your Marbec electrician and have him look over your circuit breakers, wiring and outlets as part of his regular maintenance. Flaws in your electrical system, be it with breakers, wiring or any other aspect, combined with unpredictable weather, is the recipe for a very, very bad situation.

#2 Use power surge protectors on all your appliances. Did you know that, even a lightning strike that hits miles from storm-season-tipsyour home can affect your appliances? Power surge protectors show up often in storm season tips everywhere, and there’s a reason why. Power surges can be deadly for your appliances and anything else hooked up directly into the outlet, particularly during lightning storms.

#3 Install a built-in surge protector on your circuit panel. This will protect everything hooked to the circuit panel from potentially damaging surges. Even when the power is restored after an outage, it often still does not come on right away; instead, it flickers, which shoots and cuts off electricity randomly to your appliances, ultimately causing damage.

#4 Always keep a weather radio handy. Weather alert radios are an invaluable addition to your home’s severe weather storm-season-tipkit. In case of an emergency, an outage, lightning strike or blackout, you will have access to weather updates, evacuation information (if necessary), and instructions on how to keep your family and home safe in the event of bad weather.

#5 Invest in an indoor generator. Indoor generators are a great way to take a little pressure off of the overloaded power grid during a power surge or blackout. When there’s a blackout, the indoor generator kicks in, keeping a steady flow of electricity going to your home and keeping your appliances from getting damaged. Some generators are solar-powered, which can save you energy, time and money.

Marbec: Helping You Prepare

Severe stormy weather doesn’t have to be scary, inconvenient, dangerous or costly. Following these simple storm season tips can ensure that you and your family are spared the expenses and headaches that come with unpredictable weather in Florida. Call us today to learn more about how we can help you prepare for a stormy season.

Call your Marbec electrician to help you!

Appliances can make for exciting and valuable additions to your home; however, they use a lot of electricity and can ultimately take a toll on your electrical system. We've have seen it time and again—homeowners buy new appliances that, even when they have an “Energy Star” label, use a significant amount of electricity. These homeowners are unaware, however, that the more important problem lies in the installation of these devices, taking for granted the safety precautions that were addressed (or not) during the installation process.
The old “set it and forget it” mentality that a lot of people seem to have when it comes to their new appliances is that, whether or not a Marbec Enterprises electrician is called to help install the appliance, the importance of appliance installation safety is ignored and the awareness of potential dangers and mistakes in installation is minimized. As a result, things that at the time of installation seemed trivial in the long run can cause significant problems.
Ideally, with the help of a Marbec electrician, you should have no problems installing your new electrical equipment. Here are some tips that might help you prevent safety concerns with the installation of your brand new appliances:
Check the electrical requirements of any new appliances, especially if they will be replacing older equipment. It’s important to ensure that the installation was done properly and that the transition from the old appliance to the new one is smooth.
Call your Marbec electrician to help you remove old, hardwired appliances. This is extremely important! In many older homes, appliances were hardwired to the electrical system. Removing them incorrectly can result in serious damage to the wiring.
Turn the power off before installing new appliances. Some think that this goes without saying, but you’d be surprised how many people forget about this very simple rule. Not turning off the power can result in damage to the appliance, as well as shock and possible injury to you.
Be sure to place the new appliances where they can be easily moved for cleaning. Flammable lint and dust often collect in the back of appliances, causing a fire hazard if they can’t be moved to be cleaned routinely.
Hire a Marbec electrician to check that the new appliance installation was done safely and correctly, especially if it was done in an older home.
If you have any doubts or questions about how to install your appliance safely, don’t hesitate to call us at Marbec Enterprises so we can make sure that your installation goes off without a hitch.

Lake Helen, FL
(386) 956-1594
http://marbecelectric.com

Erika is on the way Have Emergency Shelter!

Thunderstorms pose a safety hazard in several ways. Lightning is the most dangerous part of a thunderstorm, and it kills more people than hurricanes and tornadoes combined. Thunderstorms produce heavy rain, which can cause flash flooding. The strong winds from a thunderstorm can also cause widespread damage. Each of these components requires specific precautions to minimize their danger.
A thunderstorm typically has a diameter of 15 miles and lasts for 30 minutes, which is much smaller than a hurricane or winter storm. The National Weather Service places specific criteria on a severe thunderstorm. These include thunderstorms that produce hail with a diameter of at least ¾ inch, wind gusts of at least 58 mph or a tornado. Severe thunderstorms comprise about 10 percent of all thunderstorms. And we know how quickly Central Florida weather can become dangerous.
Lightning
Lightning from a thunderstorm can strike as far as 10 miles away in from any rain. This generally means that you are at risk from lightning. Lightning travels much faster than sound, which allows you to estimate your distance from the lightning. You can do this by measuring the number of seconds between the lightning and thunder. Divide this result by five to obtain the distance to the lightning in miles.
The NWS recommends that you stay indoors for 30 minutes after the last clap of thunder when you hear thunder less than 30 seconds after the lightning. This rule is known as the 30/30 lightning safety rule.
Emergency Shelter
You may need to take emergency shelter in a thunderstorm if you don’t have time to get back to your main residence before the thunderstorm hits. A shelter should generally be a sturdy structure that is closed on the top. It should also have some type of wiring or plumbing through the structure to ground it from the lightning. A vehicle with a hard top is better than no shelter at all.
Avoid taking emergency shelter in structures that are vulnerable to high winds, such as a mobile home. Outdoors shelters such as sheds, pavilions and golf’s typically will not protect you from flying debris and lightning. Avoid and report downed power lines. Bring pets under shelter to protect them during hailstorms.
Indoor Precautions
You must also take additional precautions once you are safely indoors. Unplug any electrical appliances that you don’t need immediately, since lightning can severely damage electrical appliances when they are plugged in. Refrain from activities that involve running water, such as taking a bath or shower. Running water can provide a conduit for lightning. Draw the blinds to protect yourself from broken windows.
Once the storm clears and you're safe it is time to take account of the any damage that might be done. Let Marbec Enterprises help you get back on your feet.

Heathrow, FL
(386) 956-1594
http://marbecelectric.com

Marbec Enterprises

It is the rare person who does not deal with electrical appliances today. Most people watch television, turn the oven on to cook food, or simply pop frozen foods into the microwave. With electricity pouring through virtually every home, everyone should be aware of the following electrical safety precautions:
1. Never use electrical devices that have damaged or frayed wires.
The thick wires that connect an electrical device to the wall for energy are designed to safely transfer electricity from the socket to the device. When those wires tear apart, fray, or otherwise become damaged, they can allow the flow of electricity to escape the wire. This can lead to a shock of you grab the wire in that area, but it can also lead to an electrical fire. Safety precautions require you to throw these appliances out if you cannot replace the wire.
2. Play it safe with water in close vicinity to electrical devices.
When water comes in contact with an electrical outlet or electrical device plugged into the wall, it can become live with electricity and present a danger to humans. If you have a flood in your home, do not step into the water if it is covering electrical outlets. Do not place electrical devices where they can fall into a sink or bathtub full of water.
3. Watch the placement of cords leading to electrical devices.
All electrical devices have cords, and it is common to run longer cords along the wall in order to place them where you want them. The problem is you can create a tripping hazard if you run cords along doorways or across floors in heavy traffic areas of your home. Carefully place cords where they are safe for everyone in your home.
4. If you are going to change parts on or repair an electrical device, you have to disconnect it from the outlet or otherwise shut off electrical flow to the device.
Never do work on or repair an electrical device while it is live with electricity. In most cases this just means unplugging the device before you open it up to make repairs, but when doing home improvement projects it could mean shutting off electricity from the breaker box. If you don’t know how to do this, then do not attempt the repairs on your own.
All of these electrical safety precautions should be remembered by adults working with electrical appliances. If you know someone who isn’t aware of any precaution on this list, send them here to learn. It could save a life!
When in doubt, call an electrician from Marbec Enterprises and have them take the worry out!

Heathrow, FL
(386) 956-1594
http://marbecelectric.com

Marbec on Friday

Sometimes, an electrical emergency can’t wait; sometimes, you need a 24-hour electrician to stop in as soon as possible. Here’s a look at some electrical emergencies that require immediate attention.
Air Conditioning/Heating Stops Working
On sweltering Florida summer afternoons or chilly winter nights, you just can’t wait for regular service hours to have your malfunctioning HVAC system examined. If the air conditioning or heating stops working, it could be an electrical problem, not an A/C or furnace problem.
Before you call a certified electrician, check to see if the breaker is tripped. If the breaker is tripped, go to the thermostat and turn off the heating and cooling unit. After you have turned off the thermostat, go back to the breaker and turn the breaker all the way off before resetting it to the ‘on’ position. If the breaker trips again, call a 24-hour electrician. If it doesn’t trip, turn the thermostat back on. If the breaker trips once the AC is on, you will need to contact an AC repairman.
Power Outage
If the power goes out in your home, the problem could be on your side or with the power provider. A good 24-hour electrician can discuss with you which one is the case. If your entire block loses power, it’s undoubtedly a problem with the provider. If power goes out only in your home, there’s a greater possibility that the problem is on your end. This is where a certified electrician can discuss which specific parts of your home are out and determine if you need an electrician or if you need to call your power provider.
Sparks and Flames
No matter the fire’s cause, your first call should be to the fire department. If an electrical malfunction caused the fire, your second call should be to a 24-hour electrician.
Marbec to the Rescue
You know you can count on Marbec as your certified electrician of choice. We’re always on call 24/7 to help solve electrical problems.

At Marbec Electric, our word is our bond.

Heathrow, FL
(386) 956-1594
http://marbecelectric.com/

Marbec Enterprises

Purpose:

Marbec Enterprises (MarbecElectric.com) exists to provide opportunities for each employee to maximize their personal and professional potential and to allow us to collectively making significant cultural and economic contributions to the communities in which we live and work.

Core Values:

Marbec Enterprises (MarbecElectric.com) upholds a commitment to EXCELLENCE in every endeavor; a commitment built on painstaking attention to detail and persistent communication and reflected in our superior quality of work and unparalleled customer service.

Marbec Enterprises (MarbecElectric.com) strives to provide a TEAM-ORIENTED atmosphere; one that promotes a positive attitude and encourages humble leadership and one that values each employee as an integral part of the Marbec Enterprises (MarbecElectric.com) family.

Doyle Electric embraces absolute INTEGRITY with employees, customers, end-users, consultants and every individual with whom we encounter; we are morally and ethically bound to do the right thing even when the right thing is not the easy, convenient, or profitable thing.

Marbec Enterprises (MarbecElectric.com) maintains a MERITOCRACY; an environment that seeks to reward continual personal and professional self-improvement and requires unfiltered honesty with ourselves and with each other.

Heathrow, FL
(386) 956-1594

Marbec on a thursday

Did you know roughly 1/4 of your electricity bill is used specifically for lighting? With recent changes in lighting technology, we now have the ability to control the costs of our electricity consumption more effectively. Choosing the right lightbulbs for your home or business may be confusing with all the different options we have today, so we’ve listed the three most common types in hopes to shed some light on the issue. *pun very intended
Incandescent Bulbs
Incandescent bulbs, the oldest and most common bulbs on the market, are relatively inefficient compared to other bulbs. They work by connecting an electric current that travels through a wire filament, heating up the filament until it illuminates. Unfortunately, up to 90% of the actual energy it consumes produces heat. The cost of each bulb is the lowest compared to other bulb types, but their lifespan is also the shortest, as they only last up to 2 years (based off 3 hours of use / day). With the passing of the Energy Independence and Security Act of 2007, manufacturers are working to produce more efficient incandescent bulbs that produce up to 25% less energy.
Compact Fluorescent Lamps (CFLs)
Distinctive by their bold designs, Compact Fluorescent Lamps (CFLs) are the most energy and cost effective bulb type on the market today. An electric current is driven through a tube containing argon, and a small amount of mercury vapor that triggers the actual illumination. CFLs use up to 75% less energy than traditional incandescent bulbs, cutting overall electricity costs significantly without producing excess heat. Their lifespan can be pushed up to 9 years, and technically pay for themselves after just 9 months of use, costing less than half as incandesces bulbs for the same amount of light.
Note: research has shown that CFL’s work best when left on for long periods of time, but lose efficiency when turned on and off regularly.  Because of this, it may be best not to use CFL light bulbs in areas like closets where the lights are usually just flipped on then off.
Light Emitting Diodes (LED)
Making an appearance in electronics starting in 1962, Light-Emitting Diodes (LEDs), are rapidly taking the lighting industry by storm with its highly effective technology. By connecting a diode to an electrical current, electrodes are triggered within the diode, forcing them to release photons, which we see as light. The up-front costs of LEDs are higher compared to other bulb-types, but ultimately they last up to 25% longer than traditional incandescent bulbs. Manufacturing has increased drastically in recent years, and companies are expected to offer more affordability in the near future. By reducing energy consumption by up to 80%, LEDs pave a direct path to lower electricity bills.
If you’re looking to make improvements or modifications to your electrical system, avoid the mistake of going it alone.  Let our team of experts help you make your wiring needs a reality.

Longwood, FL
(386) 956-1594
http://marbecelectric.com

Lighting Storm are a problem here in florida!

Thunderstorms pose a safety hazard in several ways. Lightning is the most dangerous part of a thunderstorm, and it kills more people than hurricanes and tornadoes combined. Thunderstorms produce heavy rain, which can cause flash flooding. The strong winds from a thunderstorm can also cause widespread damage. Each of these components requires specific precautions to minimize their danger.
A thunderstorm typically has a diameter of 15 miles and lasts for 30 minutes, which is much smaller than a hurricane or winter storm. The National Weather Service places specific criteria on a severe thunderstorm. These include thunderstorms that produce hail with a diameter of at least ¾ inch, wind gusts of at least 58 mph or a tornado. Severe thunderstorms comprise about 10 percent of all thunderstorms. And we know how quickly Central Florida weather can become dangerous.
Lightning
Lightning from a thunderstorm can strike as far as 10 miles away in from any rain. This generally means that you are at risk from lightning. Lightning travels much faster than sound, which allows you to estimate your distance from the lightning. You can do this by measuring the number of seconds between the lightning and thunder. Divide this result by five to obtain the distance to the lightning in miles.
The NWS recommends that you stay indoors for 30 minutes after the last clap of thunder when you hear thunder less than 30 seconds after the lightning. This rule is known as the 30/30 lightning safety rule.
Emergency Shelter
You may need to take emergency shelter in a thunderstorm if you don’t have time to get back to your main residence before the thunderstorm hits. A shelter should generally be a sturdy structure that is closed on the top. It should also have some type of wiring or plumbing through the structure to ground it from the lightning. A vehicle with a hard top is better than no shelter at all.
Avoid taking emergency shelter in structures that are vulnerable to high winds, such as a mobile home. Outdoors shelters such as sheds, pavilions and golf’s typically will not protect you from flying debris and lightning. Avoid and report downed power lines. Bring pets under shelter to protect them during hailstorms.
Indoor Precautions
You must also take additional precautions once you are safely indoors. Unplug any electrical appliances that you don’t need immediately, since lightning can severely damage electrical appliances when they are plugged in. Refrain from activities that involve running water, such as taking a bath or shower. Running water can provide a conduit for lightning. Draw the blinds to protect yourself from broken windows.
Once the storm clears and you're safe it is time to take
account of the any damage that might be done. Let Marbec Enterprises help you get back on your feet.

Longwood, FL
(386) 956-1594
http://marbecelectric.com

Marbec on Monday

Whether you’re doing industrial wiring or residential wiring for electricity, you’ve got a complex task ahead of you. Needless to say, industrial wiring is essentially a much more complex form of residential wiring. Let an electrician at Marbec Enterprises take care of it for you. We will simply provide you with a very basic overview of what you need to understand with regard to residential wiring and industrial wiring.
It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns. Marbec Enterprises is
trained in all aspects of electrical work.
Basics of Doing Residential Wiring
Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.
The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.
White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.
A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.
Basics of Doing Industrial Wiring
Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.
There are four types of 3-phase electrical power:
Common 3 Wire
Common 4 Wire
3 Wire with Grounded Hot Leg
Special 4 Wire
No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.
Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.
The Marbec Electrical team of highly trained commercial electrical contractors has provided top quality electrical installations for large commercial building projects in Florida for over 10 years. We are trained in all aspects of commercial electrical work and offer extensive expertise and professional service to our clients.

Longwood, FL
(386) 956-1594
http://marbecelectric.com

House Detective

With the explosion of home renovation shows such as House Detective, Holmes On Homes and Income Property , you would be hard pressed to find the person who isn’t aware that any renovation of an older home would require the specialized services of a licensed, qualified electrician. Often conjuring up images of the older, ‘quaint’, 40+ year-old home, the word “renovation” has almost become synonymous with a neglected home in disrepair, complete with bundles of wiring that could pass for extension cords. Obvious stuff that would appear glaringly unsafe to the average person.
What doesn’t come to mind is your typical, one or two-story home built anywhere from the 1980's to early 2000's.  But in today’s housing market, doing a kitchen and bath remodel could mean the difference between a sale and seeing no movement at all . Whether it’s to compete with newly built homes in a weak housing market or to increase the value and enjoyment of one’s home, a homeowner would be prudent to consult a licensed electrician when making any updates to their home. There can be unforeseen dangers when combining newer, modern appliances and lighting with existing wiring, and a licensed electrician from Marbec Enterprises can inspect and update your home’s electrical framework, ensuring its safety and increasing energy efficiency.
In a case of one trend bringing about another, the increasing popularity of in-home offices and theater rooms has  sparked the inclusion of structured wiring, or heavy-duty electrical and data cables designed to manage the latest (and yet-to-be-invented) electrical devices. Take into account that almost 50% of new homes built in 2008 included structured wiring and you can see that this trend could very well become the norm in the near future.
For questions on updating your home’s electrical infrastructure, call an electrician from Marbec Enterprises.

Longwood, FL
(386) 956-1594
http://marbecelectric.com

Marbec Enterprises

When a light switch or electrical outlet doesn’t function correctly, a professional electrician from Marbec Enterprises can trace this back to a variety of causes. First, it’s possible this non-functioning device was never connected to the wiring in your building. Secondly, the circuit affected by a switch or outlet may not be completed because of another component. For example: A switch may control an outlet which is unoccupied by a lamp or any other electrical device. Also, an outlet may be connected to a switch which is in the off position. A third cause might be related to a defective breaker, or a breaker which was tripped or turned off, but never switched back on. However, a fourth possibility may relate to a much larger problem.
Sometimes, a switch or outlet fails when it is damaged by arcing. If the arcing was caused by a connection to aluminum wiring, great potential hazards exist. If your home or building was constructed or renovated before 1972, or during the late sixties, it may contain aluminum wiring. Aluminum wiring was used legally during those years, but outlawed for installation in new homes, commercial buildings, remodels and renovations after it was identified with conditions which could lead to electrical fires.
Although aluminum wiring itself is generally no more hazardous than copper, its splices and connections with other metals present a real hazard because they can become corroded and begin arcing. Because arcing in these connections can lead to fire within surrounding materials, aluminum wire was discontinued. However, many homes still contain aluminum wiring, and research conducted by the Consumer Product Safety Commission (CPSC) reveals that buildings with aluminum wiring pose a fire risk which is 55 times greater than the risks with similar structures wired with copper. So, if you discover an electrical outlet or switch which doesn’t appear to be functioning correctly, it’s possible this outlet or switch was damaged by a connection with aluminum wiring. If you have safety questions about this type of problem, or any electrical concerns regarding your residence or commercial building, please contact an electrician at Marbec Enterprises. Our licensed electricians are trained and equipped, and they can repair any type of electrical problem

Longwood, FL
(386) 956-1594
http://marbecelectric.com

Smoke Detectors are important to have!

As a Marbec Electrician we know that your family’s safety is one of the most important things on your mind throughout the day, so we decided that now would be a good time to re-visit the subject of Smoke Detector Replacement and maintenance. As the weather is cooling off, it is very important that you are certain your family is protected in the unfortunate event that you experience a house fire. According to the U.S. Fire Administration, “Each year fires occurring during the holiday season claim the lives of over 400 people, injure 1,650 more, and cause over $990 million in damage.” Remember these lucky 7 tips to keep your family safe this holiday season by ensuring that smoke detectors are installed correctly in your home, and that they are all in working order.
Smoke Detector Battery Replacement: At least once a year
One of the most important things to remember, if you already have smoke detectors installed in your home, is to replace the batteries at least once a year. An easy way to remember this is to change the batteries in your smoke detectors when you change your clocks for daylight savings time every year. Picking up this helpful habit makes it much easier to remember.
Smoke Detector Replacement: Every 5 to 7 years
Many smoke detector manufacturers recommend replacing the smoke detector unit itself every ten years, but a smoke detector’s reliability will actually decrease after 5 to 7 years. While this may seem like an extra cost, it is certainly a small price to pay for making sure that your family will have the most reliable method of early warning in the event of a fire, providing vital time for everyone to get out safely.
Smoke Detector Cleaning: At least twice a year
Dust, cobwebs, insects, and other airborne particles that make their way into our homes can collect on sensors and contaminate the circuitry inside your smoke detector, causing it to be less effective at sensing smoke. This is one of the most forgotten factors simply because many homeowners aren’t aware of the effects that dirt and dust can have on a smoke detector. Think about how dirty the blades of your ceiling fan would get if you never cleaned them. The same dust that accumulates on your fan blades will accumulate inside your smoke detector. At least twice a year, use your vacuum cleaner wand attachment to carefully remove dust and other contaminants from the inside and outside of your smoke detector.
Smoke Detector Types: Ionization, Photoelectric, or Both
There are two commonly used types of smoke detectors, each with their own advantages and disadvantages. Ionization style smoke detectors are more responsive to quick moving, high flaming fires, while photoelectric smoke detectors are more responsive to smoldering fires that produce more smoke. You can never know what type of fire will happen in your home, so a great option to ensure the best protection is to choose smoke detector units that provide both ionization and photoelectric detection of smoke and fire.
Smoke Detector Location: Key guidelines for safe placement
Smoke detector placement is highly important in order for them to work properly. When installing smoke detectors in your home, it is ideal to have a smoke detector in each room, but at the very least, you should install smoke detectors on every level of your home, and in hallways near each bedroom to increase the likelihood that your family will be able to hear them even while sleeping. Smoke detectors should be placed 6 to 12 inches from the ceiling, and you should avoid installing them near vents, fireplaces, or kitchen appliances to reduce the accumulation of dust, soot, and oily residues from cooking.
Interlinked Smoke Detectors: Whole house warning
Modern smoke detector systems are more than simply individual detectors. It is recommended to install a system that allows all of the smoke detectors in your home to communicate with each other causing all of the detectors to alert of the fire if any single detector senses one. These systems can be wired directly into your homes electrical system, or allow wireless communication between each smoke detector. This has been a major advancement in smoke detector technology, allowing more time for residents to escape if a fire begins in any area of the home. These systems are especially valuable in late-model homes where the master bedroom is often on the opposite side of the house from children’s rooms.
Smoke Detector Testing: At least twice a year
We often take for granted that a smoke detector will simply work as designed once it is installed, but as you can see from this list, there are a lot of factors that go into a reliable smoke detection system. At the very least, make sure that you test your smoke detectors twice a year using the test button that is located on the smoke detector unit itself. When testing interlinked smoke detector systems, be sure to verify that all of the other detectors in your home alert when you test each unit individually. Even if a unit alerts when you test it, if it does not cause the other units in the home to alert, that means that there is an issue with communication between the units, and it should be inspected by a licensed Marbec Electrician.
If you have any concerns about your smoke detector system, or any other electrical projects in your home, the electricians at Marbec Enterprises. will be happy to help. Reach out to us by phone or through the “Contact Us” page on our website, and let our professional electrical technicians ensure your family’s safety by guaranteeing that the job is done right!

Longwood, FL
(386) 956-1594
http://marbecelectric.com